⚡ VoltEdge

kW to Amps Single Phase Calculator

The workhorse conversion for homes and small businesses — type in your load and watch the current it draws on a single-phase supply.

Calculator Input

LIVE  Live calculation — type and watch the result.

The nameplate rating of the appliance — check the label or manual if you are unsure.
230 V is standard in most of the world; 120 V or 240 V in North America.
0.9 is a sensible default. Heaters sit near 1.0; motors run lower.

Conversion Result

—
Enter values to calculate

Formula Used

—

How Single-Phase Conversion Works

1

Enter the power in kilowatts

Use the rated load of the device — the figure printed on its nameplate or datasheet.

2

Enter the supply voltage

The voltage at the socket or breaker feeding the load, e.g. 230 V.

3

Set the power factor

Pick 1.0 for pure heating loads, 0.9 for mixed loads, lower for motors.

4

Read the current

The calculator divides watts by volts × power factor and updates instantly.

Single-Phase Formula

Single-phase: I = (kW × 1000) ÷ (V × PF)

Multiply the kilowatts by 1000 to get watts, then divide by voltage times power factor. That is the whole method.

From watts: I = W ÷ (V × PF)

If the rating is already in watts, skip the ×1000 step and divide directly.

Reverse (amps → kW): kW = (I × V × PF) ÷ 1000

To work backwards, multiply amps by volts and power factor, then divide by 1000.

Where Single-Phase Power Is Used

Single-phase supply feeds almost every home: lights, sockets, kitchen appliances, washing machines, and small air-conditioners. Small shops, offices, and workshops run on it too — anywhere the loads are modest and one live conductor plus neutral is enough.

Power factor on these loads usually lands between 0.85 and 0.95. Heating elements (kettles, ovens, space heaters) sit near 1.0, while anything spinning a motor — fridges, pumps, compressors — drags it lower. As a worked example: 2 kW at 230 V with PF 0.9 gives (2 × 1000) ÷ (230 × 0.9) = 9.66 A.

Beyond the house, single-phase shows up in portable generators, RV hookups, construction-site temporary supplies, and light commercial units such as cafes and corner shops. Home EV chargers up to about 7 kW are single-phase as well — a 7 kW charger on 240 V draws 29.17 A on one dedicated circuit. Single-phase starts to run out of steam above roughly 10–15 kW, which is where properties graduate to a three-phase service.

Split-Phase 120/240 V vs 230 V Systems

North America feeds homes with 120/240 V split-phase; most of the rest of the world uses a single 230 V line-to-neutral — and the arithmetic is identical either way. In a North American panel, a center-tapped transformer delivers two 120 V legs that are 180° apart. Small loads connect across one leg and neutral for 120 V; heavy loads — dryers, ovens, EV chargers — connect across both legs for 240 V. Outside North America there is just one 230 V hot conductor plus neutral, so every socket sees the same voltage.

For the calculator, the only thing that matters is the voltage the load actually sees. A US toaster on a kitchen socket is a 120 V load; the same house’s electric dryer is a 240 V load. Enter 120 or 240 accordingly — the formula does not care which continent you are on. Note that 220 V, 230 V, and 240 V are all the same nominal system seen through different eras of standardization; the few volts of difference shift the answer by barely 4%, well within the margin you should be leaving anyway.

Power Factor Around the House

Most of what a house runs sits between 0.85 and 0.95 power factor, so ignoring it introduces a small but real error. Anything that is basically a resistor — kettles, toasters, ovens, space heaters, incandescent bulbs — runs at essentially 1.0, because current and voltage stay in step. Anything with a motor — fridge compressors, washing machines, air-conditioner units, pool pumps — lands around 0.8 to 0.9. Modern LED drivers usually manage about 0.9, while cheap phone chargers and small electronics can dip toward 0.7.

A practical rule of thumb: use 1.0 for pure heating loads, 0.85 for anything with a motor, and 0.9 as the household default when you are totaling up a mixed set of loads. At PF 0.9 the current is about 11% higher than the naive watts ÷ volts figure; at PF 0.85 it is about 18% higher. That is the difference between a cable that runs warm and one that runs hot — worth the one extra keystroke.

Sizing a Breaker: the 80% Continuous-Load Rule

A breaker should carry a continuous load at no more than 80% of its rating — so you size the breaker at 125% of the load current. A continuous load is anything expected to run at full tilt for three hours or more: water heaters, EV chargers, space heaters, grow lights. Breakers are thermal devices, and running one at 100% for hours lets heat build up in the panel until it trips on a warm afternoon — or worse, doesn’t trip when it should.

Worked example: a 3.5 kW storage water heater on 230 V with PF 1.0 draws (3.5 × 1000) ÷ 230 = 15.22 A. Multiply by 1.25 for the continuous-load margin: 19.02 A. The next standard breaker size up is 20 A, so this heater gets a 20 A dedicated circuit with cable rated for at least 20 A. Intermittent loads — kettles, microwaves, power tools — are not continuous by this definition, but most electricians still keep a comfortable margin rather than sizing to the exact amp.

Amps per Kilowatt: Quick Reference

Bookmark numbers: 1 kW draws about 4.35 A at 230 V, or 8.33 A at 120 V — and power factor nudges both upward. This table covers the common residential voltages at PF 1.0 and PF 0.9:

VoltageAmps per 1 kW (PF 1.0)Amps per 1 kW (PF 0.9)
120 V8.33 A9.26 A
220 V4.55 A5.05 A
230 V4.35 A4.83 A
240 V4.17 A4.63 A

Read it two ways. Going up: a 2 kW heater at 230 V, PF 1.0, is simply 2 × 4.35 = 8.70 A. Going across: the same kilowatt at 120 V needs nearly twice the current as at 230 V, which is why North American branch circuits top out at lower wattages per breaker than European ones.

Worked Examples

Example 1 — electric kettle. A 2 kW kettle on 230 V is a pure heating load, so PF = 1.0. I = (2 × 1000) ÷ (230 × 1.0) = 8.70 A. A standard 13 A UK socket or 16 A European circuit handles it with room to spare — which is why kettles just work everywhere.

Example 2 — window air conditioner. A 1.5 kW unit on a 120 V US circuit, compressor motor at PF 0.85. I = (1.5 × 1000) ÷ (120 × 0.85) = 14.71 A. That is uncomfortably close to a 15 A breaker, and the compressor’s startup surge is higher still — this unit belongs on a dedicated 20 A circuit, not shared with anything else.

Example 3 — home EV charger. A 7 kW charger on 240 V, PF 1.0 (chargers are essentially unity power factor). I = 7000 ÷ 240 = 29.17 A. Charging is a continuous load, so apply the 125% rule: 29.17 × 1.25 = 36.46 A, which means a 40 A dedicated circuit with appropriately rated cable. This is the single biggest load in most homes, and it is why installers run a fresh circuit from the panel rather than tapping an existing one.

Common Mistakes and Safety

The most expensive mistake is forgetting the power factor — it understates the current by 10–20% and lands you on cable that runs hot. Other classics: entering 240 V for a load that actually sees 120 V (halving the answer), mixing up kW and kVA when sizing a generator, and sizing a breaker at exactly the load current with no margin for continuous duty.

On safety: switch off at the breaker before touching any wiring, verify the circuit is actually dead with a tester (never trust the label alone), and never bypass or upsize a breaker to stop nuisance tripping — a tripping breaker is telling you something. Anything beyond swapping a like-for-like accessory belongs to a licensed electrician, and this page is an arithmetic reference, not wiring instruction.

Frequently Asked Questions

How do I convert kW to amps on single-phase?
Divide the watts by the product of volts and power factor: I = (kW × 1000) ÷ (V × PF). That is the complete method.
What power factor should I enter?
Use 1.0 for pure heating loads, 0.9 as a general default, and 0.8–0.85 for motor-driven equipment. The lower the power factor, the higher the resulting amps.
Why is single-phase current higher than three-phase for the same kW?
The same power travels over one conductor instead of three, so that single conductor must carry all of it. Three-phase splits the power across three conductors, dropping the per-conductor current.
Is 230 V always single-phase?
In most homes, yes — 230 V line-to-neutral is the standard single-phase residential supply outside North America. Three-phase supplies are measured line-to-line at 400 V in the same regions.
Can I size a generator with this calculator?
Yes. Enter the total kW of the loads the generator must feed and its rated voltage to estimate the current each leg must handle.
How many amps does a 2 kW appliance draw at 230 V?
8.70 A at PF 1.0 — (2 × 1000) ÷ 230 = 8.70. If it has a motor (PF 0.9), the same 2 kW draws 9.66 A.
What size breaker for a 3.5 kW water heater at 230 V?
The heater draws 15.22 A. Water heating is a continuous load, so multiply by 1.25 (19.02 A) and use the next standard size up: a 20 A dedicated circuit.