Electricity Cost at a Glance
Any appliance’s running cost comes from three numbers: its watts, its hours of use per day, and your rate per kWh. Multiply them — watts × hours ÷ 1000 × days × rate — and you have the monthly cost. A 1500 W space heater running 6 hours a day for 30 days at $0.15/kWh uses 270 kWh and costs $40.50 per month.
Most people are surprised twice: first by how much heating and cooling cost, then by how little efficient lighting costs. A 10 W LED bulb running 5 hours daily costs about $0.23 a month — the heater costs roughly 175 times more. The calculator above turns any nameplate wattage into daily kWh, monthly kWh, monthly cost, and yearly cost instantly; the guide below explains the formulas, shows verified worked examples, and covers the billing details that change the real answer.
The Formulas
The kilowatt-hour (kWh) is the unit your utility bills — 1 kWh means 1000 watts running for one hour. Dividing watts × hours by 1000 converts watt-hours to kilowatt-hours. Everything else is multiplication: more days, more hours, or a higher tariff each scale the cost proportionally.
Worked Examples
Example 1 — Space heater: 1500 W × 6 h/day ÷ 1000 = 9 kWh/day; × 30 days = 270 kWh/month; × $0.15 = $40.50/month; × 12 = $486/year. This is why electric resistance heating dominates winter bills.
Example 2 — LED bulb: 10 W × 5 h/day ÷ 1000 = 0.05 kWh/day; × 30 = 1.5 kWh/month; × $0.15 = $0.22/month — about $2.70 per year. Replacing a 60 W incandescent (which would cost $1.35/month) pays for the LED in weeks.
Example 3 — Air conditioner: 3500 W × 8 h/day ÷ 1000 = 28 kWh/day; × 30 = 840 kWh/month; × $0.15 = $126/month — $1,512 per year. A one-degree thermostat change typically moves this 3–5%.
Example 4 — Refrigerator: the nameplate says 150 W, but the compressor cycles — assume 8 effective running hours per day. 150 × 8 ÷ 1000 = 1.2 kWh/day; × 30 = 36 kWh/month; × $0.15 = $5.40/month. Duty cycle (the fraction of time actually running) is the key number for cycling appliances.
Where to Find the Wattage
Nameplate. Every appliance has a rating label listing watts (or amps — convert with the amps to watts calculator). Use the rated watts for heaters and kettles, which run at full power.
Measure it. A plug-in power meter ($15–25) shows real watts, including standby draw. For hardwired loads, a clamp meter on a single conductor gives amps — convert to watts from there.
Estimate duty cycle. Fridges, ACs, and water heaters cycle on and off. If a 2000 W water heater runs 3 hours out of 24, use 3 hours in the calculator — not 24. When unsure, a plug-in meter left for a day gives the true kWh directly.
Typical Appliance Wattages and Hourly Cost
At $0.15/kWh, here is what common appliances cost per hour of actual running time:
| Appliance | Typical Watts | Cost per Hour |
|---|---|---|
| LED bulb | 10 W | $0.002 |
| Phone charger | 10 W | $0.002 |
| Laptop | 60 W | $0.009 |
| TV (LED) | 100 W | $0.015 |
| Refrigerator (running) | 150 W | $0.023 |
| Washing machine | 500 W | $0.075 |
| Microwave | 1000 W | $0.15 |
| Kettle | 1500 W | $0.23 |
| Space heater | 1500 W | $0.23 |
| Hair dryer | 1800 W | $0.27 |
| Dishwasher (heating) | 1800 W | $0.27 |
| Oven | 2400 W | $0.36 |
| Air conditioner | 3500 W | $0.53 |
| Water heater | 4000 W | $0.60 |
| EV charger | 7000 W | $1.05 |
The pattern is unmistakable: anything that makes heat from electricity costs roughly 100× more per hour than lighting. When a bill looks wrong, the culprit is almost always a heating or cooling load running longer than assumed — not the light bulbs.
Estimating a Whole-House Bill
To estimate a full monthly bill, list your major loads with realistic daily hours, run each through the calculator, and add the kWh: for example, a water heater (4000 W × 3 h = 12 kWh), air conditioner (3500 W × 6 h = 21 kWh), fridge (1.2 kWh), lighting and electronics (3 kWh), and laundry/dishwasher (2 kWh) total about 39 kWh/day — 1,170 kWh/month, or $175.50 at $0.15/kWh. Compare against 2–3 past bills to calibrate: if the estimate is consistently low, some load is running longer than you think (check the water heater thermostat and AC setpoint first); if high, your effective hours are lower. Two or three iterations usually land within 10% of the real bill — close enough to test whether an efficiency upgrade will pay off.
Reading Your Bill: Finding Your True Rate
The rate to use in the calculator is your effective rate — total bill divided by total kWh — not just the headline tariff. A bill showing $87.40 for 540 kWh means an effective rate of $0.162/kWh, even if the tariff line says $0.13. The difference is fixed service charges, taxes, and surcharges spread across your usage. Recompute this every few months: as usage rises or tariffs change, the effective rate moves, and so does every estimate. Commercial bills add a second trap — demand charges billed on peak kW rather than kWh. If your bill has a demand line, reducing peak draw (staggering large loads) can save more than reducing total energy.
What Changes the Real Bill
- Tiered tariffs — many utilities charge more per kWh as monthly usage crosses thresholds. Heavy users pay a higher average rate than the first-tier price on the bill.
- Time-of-use rates — peak-hour electricity can cost 2–3× the off-peak rate. Shifting water heating, EV charging, and laundry to off-peak hours cuts cost without cutting usage.
- Standby (phantom) loads — TVs, chargers, and set-top boxes draw 1–10 W around the clock. Ten devices at 5 W average cost 36 kWh/month — about $5.40 at $0.15/kWh — for doing nothing.
- Power factor surcharges — residential bills ignore it, but commercial tariffs may penalize low power factor. Industrial users should check before assuming the simple formula.
- Taxes and fixed charges — the per-kWh rate on your bill’s tariff line is not the all-in cost. Divide the total bill by total kWh for your true effective rate.
Cutting the Cost
Attack the biggest numbers first: heating, cooling, and water heating are typically 60–70% of a home’s bill. A heat pump delivers 3–4× the heat per kWh of resistance heating. LED lighting, full laundry loads in cold water, and eliminating standby draw handle the rest. Use this calculator on each major appliance — rank them by yearly cost, and efficiency upgrades will pay for themselves in a predictable number of months.
Common Mistakes
- Confusing watts with kilowatt-hours. Watts are power (rate); kWh is energy (amount). A 1500 W heater running 1 hour uses 1.5 kWh — the “per hour” is already inside the kWh.
- Using switched-on hours instead of running hours. A TV “on” 6 hours but actually displaying content for 4 draws less than the nameplate suggests. Use effective running hours.
- Ignoring the tariff structure. A single flat rate is the exception, not the rule. Check for tiers and time-of-use bands before trusting the estimate.
- Forgetting seasonal variation. Heaters and ACs run far more in extreme months. For a yearly estimate, calculate a summer month and a winter month separately and average them.
- Trusting the nameplate maximum. Nameplates show maximum draw. A “2000 W” microwave at 50% power setting averages far less — measure or derate.
Keep Calculating
Find any load’s watts with the amps to watts calculator, convert between power units on the kW to amps and kVA to amps pages, and look up typical appliance consumption on the kW to amps chart.