⚡ VoltEdge

Amps to kW Calculator

Convert current to kilowatts — for any circuit type.

Calculator Input

LIVE  Live calculation — type and watch the result.

Measured with a clamp meter or from the nameplate.
Your supply voltage — 120, 230, 400, etc.
Use 1.0 for heaters, ~0.85 for motors. Ignored on DC.

Conversion Result

—
Enter values to calculate

Formula Used

—

Amps to kW at a Glance

To convert amps to kilowatts, multiply amps by volts (and by power factor on AC), then divide by 1000. For three-phase, multiply by an extra 1.732 (√3) first. In short: kW = amps × volts ÷ 1000, adjusted for circuit type. A 32 A load on 230 V single-phase is 32 × 230 ÷ 1000 = 7.36 kW.

This conversion runs in the opposite direction from the headline kW-to-amps calculation, and it is the one you reach for when the known quantity is current. Clamp meters measure amps; nameplates list amps; breakers are rated in amps — but energy bills, generator ratings, and load schedules all speak kilowatts. The calculator above bridges the two for DC, single-phase, and three-phase circuits, and the guide below walks through the formulas, verified worked examples, and the errors to avoid.

The Three Formulas

DC:  kW = (I × V) ÷ 1000
Single-phase AC:  kW = (I × V × PF) ÷ 1000
Three-phase AC:  kW = (√3 × I × V × PF) ÷ 1000

I is current in amps, V is voltage in volts, and PF is power factor — 1 for DC and resistive loads, roughly 0.8–0.95 for motors. The division by 1000 simply converts watts to kilowatts. On three-phase, always use line-to-line voltage (400 V or 415 V, never 230 V) with the √3 formula.

Worked Examples

Example 1 — Household circuit (single-phase): a clamp meter reads 32 A on a 230 V circuit, PF 1. kW = (32 × 230 × 1) ÷ 1000 = 7360 ÷ 1000 = 7.36 kW. That circuit is carrying over 7 kW — near the limit of a 32 A breaker.

Example 2 — Industrial motor (three-phase): a motor draws 25 A on 400 V three-phase at 0.87 PF. kW = (1.732 × 25 × 400 × 0.87) ÷ 1000 = 15068 ÷ 1000 = 15.07 kW. Note this is the electrical input power; the motor’s shaft output is lower by its efficiency.

Example 3 — Battery system (DC): a 48 V battery bank discharging at 10 A. kW = (10 × 48) ÷ 1000 = 0.48 kW — about half a kilowatt of real power.

Example 4 — Workshop feeder (three-phase): 63 A on 400 V three-phase at 0.85 PF. kW = (1.732 × 63 × 400 × 0.85) ÷ 1000 = 37099 ÷ 1000 = 37.10 kW. A feeder sized for this needs 63 A protection minimum, 80 A for continuous loading.

From Clamp Meter to Kilowatts: A Field Workflow

Here is the practical sequence electricians and energy auditors follow to turn a current reading into kilowatts:

1) Work safely. You will be inside a live panel. Wear rated PPE, keep one hand clear, and never touch bare conductors. If you are not qualified, hire someone who is — no reading is worth an arc flash.

2) Clamp a single conductor. Open the clamp around one live wire only — never around a whole cable, where opposing currents cancel and read near zero. In a panel, the load side of a breaker is the usual spot.

3) Measure every phase. On three-phase, clamp L1, L2, and L3 separately. Unbalanced loads are normal; use the average for a rough kW figure, or convert each phase and add them for precision.

4) Record voltage at the same time. Measure line voltage while the load runs — it sags under load, and using the nominal 400 V when the real value is 388 V introduces a 3% error.

5) Convert and log. Plug amps, measured volts, and power factor into the calculator. Log readings over a day or week: a single snapshot misses cycling loads, and the average — not the peak — is what the energy bill reflects.

kW vs kVA vs kWh — Don’t Mix Them Up

Three similar-looking units cause most of the confusion around this conversion. kW (kilowatts) is real power — the rate at which useful work gets done right now. kVA (kilovolt-amps) is apparent power — everything the supply must deliver, including the reactive current that does no work. They are related by power factor: kW = kVA × PF. A generator rated 100 kVA at 0.8 PF delivers 80 kW of real power, but its windings carry current for the full 100 kVA.

kWh (kilowatt-hours) is energy — power sustained over time. A 2 kW heater running for 3 hours consumes 6 kWh. Your electricity bill charges for kWh, your breaker cares about amps, and your generator is rated in kVA or kW. Converting amps to kW answers “how much power is flowing now”; multiplying by hours answers “how much energy was used.”

The practical rule: size wires and breakers from amps, size generators and transformers from kVA, estimate bills from kW × hours = kWh, and compare appliance ratings in kW. Each unit has exactly one job.

Quick Reference: Common Currents to kW

Handy conversions at 230 V single-phase (PF 1) and 400 V three-phase (PF 0.85):

Current230 V 1-phase400 V 3-phase
10 A2.30 kW5.89 kW
16 A3.68 kW9.42 kW
20 A4.60 kW11.78 kW
32 A7.36 kW18.84 kW
63 A14.49 kW37.10 kW
100 A23.00 kW58.89 kW

Why Converting Amps to kW Matters

Energy auditing. Walk a facility with a clamp meter, record the amps on each feeder, convert to kW, multiply by operating hours — you now have a kWh consumption profile and can estimate the electricity bill before it arrives. This is the standard first step of a commercial energy audit.

Load scheduling and demand charges. Industrial tariffs penalize peak kW demand, not total energy. Converting measured amps to kW shows which equipment drives the peak — and therefore which loads to stagger.

Generator and UPS verification. A generator rated 45 kVA delivers about 36 kW at 0.8 PF. If your measured loads convert to 34 kW, you are running at 94% — too close for comfort once motor starting surges are considered. Convert first, then decide whether the set is adequate.

Equipment selection. Heaters, EV chargers, and HVAC units are sold by kW, but your panel schedule lists breaker amps. Converting the panel’s spare amps to kW tells you the largest appliance the panel can still accept — try it, then confirm with the breaker sizing calculator.

Common Mistakes

Keep Calculating

This page pairs naturally with the kW to amps calculator (the reverse conversion), amps to watts for watt-level answers, and kVA to amps when you are working from generator ratings. Once the kilowatts are known, the breaker size calculator tells you how to protect the circuit.

Frequently Asked Questions

How many kW is 20 amps at 230 V?
4.6 kW at PF 1 (single-phase): 20 × 230 ÷ 1000. At PF 0.8, it is 3.68 kW.
How many kW is 100 amps three-phase 400 V?
About 58.9 kW at PF 0.85: 1.732 × 100 × 400 × 0.85 ÷ 1000.
Is amps × volts ÷ 1000 the same as the kW formula?
Yes — identical. Watts = amps × volts, and kilowatts = watts ÷ 1000.
Why does my motor’s kW not match the nameplate?
Nameplates list mechanical shaft output in kW. Electrical input is higher: input kW = shaft kW ÷ efficiency. A 15 kW motor at 90% efficiency draws 16.7 kW electrically.
Can I convert amps to kW for a battery?
Yes — use the DC formula. A 100 A draw on a 12 V battery is 1.2 kW.
Does wire length affect this conversion?
No — amps to kW is a point calculation. Length matters for voltage drop, which is a separate calculation.
How do I get kWh from this?
Multiply the kW result by operating hours. A 7.36 kW load running 5 hours uses 36.8 kWh.