How the DC Calculator Works
Enter the power in kilowatts
DC power is always real power — the kW figure equals the total power consumed, with no reactive part.
Enter the DC voltage
Use the system voltage: 12, 24, 48, 120 or 380 V are the usual suspects.
Skip the power factor
DC voltage and current are always in phase, so power factor is 1.0 by definition. Nothing to enter.
Read the current
DC current is steady, not alternating — the result is the continuous current draw.
DC Formulas
One division. No power factor, no √3 — watts divided by volts gives amps, done.
If your rating is already in watts, divide it straight by the voltage.
Going the other way? Multiply amps by volts, then divide by 1000.
Why DC Math Is the Simplest of All
DC is the only circuit type where the conversion is genuinely one step: amps = watts ÷ volts, with nothing else to look up. On alternating current, voltage and current rise, fall, and reverse dozens of times per second, and can drift out of step — power factor measures how well they line up. Direct current never takes turns: the voltage is a flat line, the current flows in one direction only, and the two are always perfectly in step. The power factor is therefore 1.0 by definition, and simply vanishes from the arithmetic.
There is also no √3, no line-to-line versus line-to-neutral question, and no waveform geometry to untangle. The whole physics of a DC circuit in steady state fits into one equation, P = V × I, and the calculator above is that equation rearranged to solve for I. The only judgment call is which voltage to enter — the rest is division.
Common DC Voltages and Their Currents
On a DC system, the voltage you pick decides your current: 1 kW draws four times the amps at 12 V as at 48 V. The table shows standard DC voltage levels, where each one lives, and the current 1 kW draws at each:
| Voltage | Typical uses | Amps per 1 kW |
|---|---|---|
| 12 V | Cars, caravans, small off-grid setups | 83.33 A |
| 24 V | Trucks, boats, telecom backup strings | 41.67 A |
| 48 V | Solar battery banks, data centers, e-bikes | 20.83 A |
| 120 V | DC traction, older industrial systems | 8.33 A |
| 380–400 V | EV battery packs, fast-charging rails | 2.63–2.50 A |
| 800 V | Newest EV platforms | 1.25 A |
Notice the pattern: every doubling of voltage halves the current. That single relationship explains why electric cars moved from 400 V to 800 V architectures — the same charging power flows through half the current, so cables and connectors stay slimmer. It also explains why nobody runs a house on 12 V: 1 kW at 12 V is 83.33 A, a current that needs cable as thick as your finger.
Where DC Power Shows Up
Battery banks, solar panels (on the panel side, before the inverter), electric vehicles, data-center bus bars, telecom gear, and electrochemical processes all run on DC. Modern 48 V DC distribution is spreading through data centers because it cuts conversion losses compared with AC distribution.
A handy reference: 1 kW at 48 V DC = 20.83 A. Solar panels natively produce DC; the inverter only enters the picture when that power is converted for household AC use — and this calculator covers the DC side of that system.
Batteries are the other giant DC application — car, home-storage, and phone batteries are all DC sources, as is everything they feed before any conversion stage. Telecom towers have run on −48 V DC backup strings for decades so equipment keeps running straight off the batteries when the grid fails, and off-grid cabins standardize on 24 V or 48 V: high enough to keep currents sane, low enough to work with safely.
Always run this calculator on the DC side of a system separately from the AC side. A 2 kW inverter might draw 41.67 A from its 48 V battery bank while delivering only about 9.66 A to a 230 V AC load — same power, two completely different currents, each sized with its own formula.
The Low-Voltage Penalty: Current, Heat, and Wire Size
Low voltage is expensive in copper: every halving of voltage doubles the current for the same power, and wires are sized by current, not by power. A 1 kW load at 48 V draws 20.83 A and fits comfortably on ordinary 4 mm² cable. The same 1 kW at 12 V draws 83.33 A — heavy battery cable and a chunky fuse. The work is identical; only the delivery plumbing changes.
Heat makes the penalty worse than it looks. The power wasted as heat in a wire grows with the square of the current (I²R), so the 12 V wire carrying four times the current produces sixteen times the heat of the 48 V wire for the identical kilowatt delivered.
Voltage drop eats your margin
Current through resistance also steals voltage along the cable, and on a low-voltage DC system there is little voltage to spare. Take a 2 kW load on a 48 V bank, fed through 10 m of 2.5 mm² copper (20 m round trip, about 0.134 Ω of resistance). At 41.67 A the drop is 5.60 V — 11.7% of the supply — and 233.3 W burns off as heat in the cable. Now try 1 kW at 12 V over just 5 m of 4 mm² cable: the 83.33 A drops 3.50 V, which is 29.2% of the supply, wasting 291.7 W. Nearly a third of the power never arrives.
The practical rule is simple: keep DC cable runs short, size the cable generously, and when the numbers start looking ugly, raise the system voltage. Going from 12 V to 48 V quarters both the current and the percentage voltage drop on the same cable.
Worked Examples
Example 1 — 48 V solar battery bank. A 2 kW inverter draws from a 48 V battery bank. I = (2 × 1000) ÷ 48 = 41.67 A. Size the battery cable and fuse for at least 50 A, and keep the run between battery and inverter short — this is the highest-current stretch in the system.
Example 2 — 400 V EV charging. A home DC charger delivers 5 kW to a car at 400 V. I = 5000 ÷ 400 = 12.50 A. That modest current is the payoff of a high-voltage pack: slim, cool charging cables. At 12 V the same 5 kW would demand 416.67 A — a current no practical charging cable could carry.
Example 3 — why 12 V systems stay small. Compare 1 kW at the two common off-grid voltages: at 12 V it is 83.33 A, at 48 V it is 20.83 A. A 3 kW load at 12 V would pull 250.0 A — welding-cable territory — while at 48 V it is a manageable 62.50 A.
Common Mistakes
The classic DC mistake is borrowing an AC formula. Dividing by a power factor or by √3 on a DC circuit inflates the current — by about 11% with a 0.9 power factor, or 73% with √3 — so you buy cable and fuses far heavier than needed. On DC, watts ÷ volts is the entire method; anything extra in the denominator is wrong.
- Using the nameplate voltage instead of the working voltage. A “12 V” battery reads about 14.4 V while charging and sags toward 11.5 V when nearly flat — a swing that moves the current roughly ±15%, so size wiring for the lowest voltage the system will see under load.
- Sizing fuses by watts instead of amps. Protection devices are rated in amps because they respond to current. Convert to amps first, then pick the fuse — and put it as close to the battery as physically possible, since every centimeter of unfused cable is unprotected.
- Forgetting which side of the inverter you are on. The battery side always carries far more current than the AC output: a 2 kW inverter draws 41.67 A from its 48 V bank while feeding roughly 9.66 A to a 230 V load — size each side with its own numbers.
- Ignoring inrush. DC motors and large capacitors gulp a brief surge at switch-on, several times the running current. Size fuses and breakers with a time-delay characteristic to ride through the startup pulse.
DC Safety Essentials
Respect DC precisely because it looks tame: a battery bank can dump thousands of amps into a short circuit with no warning. Unlike AC, a DC arc never crosses zero, so once it strikes — a wrench dropped across battery terminals, for instance — it sustains far longer and burns hotter. That is why DC circuits demand DC-rated switches, breakers, and fuses.
Work with insulated tools and remove metal jewelry before working near battery terminals. Double-check polarity before connecting anything — reversed polarity on DC destroys electronics instantly, where AC equipment would simply not care. Treat this page as what it is: an educational reference for the arithmetic, not a substitute for a licensed electrician.