kVA to kW at a Glance
Generators, transformers, and UPS units are rated in kVA (apparent power), but your loads consume kW (real power). The bridge between them is the power factor: kW = kVA × PF. A 100 kVA generator at 0.8 power factor delivers 80 kW of usable power, with the remaining capacity tied up as 60 kVAR of reactive power. The calculator above shows all three values — real, apparent, and reactive — the moment you enter kVA and power factor.
Apparent, Real, and Reactive Power
Think of it as a right triangle. The hypotenuse is apparent power (kVA) — everything the equipment must carry. The horizontal leg is real power (kW) — the part that does useful work, spinning motors and heating elements. The vertical leg is reactive power (kVAR) — current that builds magnetic fields in motors and transformers each AC cycle, then returns to the source. The angle between kVA and kW is set by the power factor: PF = kW ÷ kVA = cos φ. At PF 1 the triangle collapses to a line and kVA equals kW; at PF 0.8, a fifth of the capacity is reactive.
Worked Examples
Example 1 — The classic triangle: 100 kVA at 0.8 PF. kW = 100 × 0.8 = 80 kW; kVAR = √(100² − 80²) = √3600 = 60 kVAR. The 60-80-100 triangle is the textbook case — memorize it and you can sanity-check any conversion.
Example 2 — Site generator: 45 kVA at 0.85 PF. kW = 45 × 0.85 = 38.25 kW; kVAR = √(45² − 38.25²) = √(2025 − 1463.06) = √561.94 = 23.7 kVAR. This generator can carry 38.25 kW of real load — a 40 kW load would overload it even though “45” looks bigger than “40”.
Example 3 — UPS sizing: a 3 kVA UPS at 0.9 PF (typical for modern UPS units). kW = 3 × 0.9 = 2.7 kW; kVAR = √(9 − 2.7²) = √1.71 = 1.3 kVAR. Your servers may draw at most 2700 W — plug in 3000 W of equipment and the UPS trips on overload despite being “3 kVA”.
Example 4 — Motor load: equipment drawing 15 kVA apparent at 0.87 PF. kW = 15 × 0.87 = 13.05 kW; kVAR = √(225 − 13.05²) = √54.7 = 7.4 kVAR. The utility sees and bills infrastructure for 15 kVA; only 13.05 kW does work.
Why Power Factor Decides the Answer
The same kVA means very different kW at different power factors: 100 kVA is 100 kW of useful power at PF 1 (a data center full of servers with PFC power supplies) but only 70 kW at PF 0.7 (an old factory full of lightly loaded motors). Two consequences follow. First, equipment must be sized from kVA: windings, breakers, and cables carry total current, so a transformer feeding 80 kW at 0.7 PF needs a 114 kVA rating, not 80. Second, utilities penalize low power factor — large customers pay demand charges on kVA or face PF penalties, which is why factories install capacitor banks for three-phase power factor correction.
Sizing Equipment From kVA
When you buy a generator, you buy kVA. The standard assumption is 0.8 PF, so a “100 kVA” generator is really an 80 kW generator — size your loads against the 80, not the 100. Transformers follow the same logic: a 500 kVA transformer at 0.85 PF serves 425 kW of real load. UPS units are the trap most people fall into, because UPS power factors vary (0.9 on modern units, 0.7–0.8 on older ones): always check whether the kW rating or only the kVA rating is published, and convert with the unit’s actual PF. For the current side of sizing, our kVA to amps calculator converts equipment ratings to the amps your distribution board must handle.
Power Factor Correction in Practice
Low power factor is fixable. Capacitor banks installed at the factory switchboard supply the reactive current locally, so the utility transformer no longer has to. The math is a vector subtraction on the power triangle. Take a 100 kVA load at 0.7 PF: real power is 70 kW and reactive power is √(100² − 70²) = √5100 = 71.4 kVAR. Correct the plant to 0.95 PF and the apparent power drops to 70 ÷ 0.95 = 73.7 kVA, with reactive power now √(73.7² − 70²) = √531.7 = 23.1 kVAR. The capacitor bank must supply the difference: 71.4 − 23.1 = 48.4 kVAR — that is the size you order.
The payoff is freed capacity: the same transformer and cables now have 26.3 kVA of headroom for expansion, and the utility’s PF penalty disappears. Two cautions: correction must be sized from measured load, not nameplate totals, because an oversized bank over-corrects to a leading power factor that can resonate with transformer inductance; and detuned reactors are needed where harmonics from variable-speed drives are present, or the capacitors themselves become the failure point.
kVA on Your Electricity Bill
Small consumers are billed only for kWh — which is why homes never see power factor. Large commercial and industrial customers also pay demand charges based on their peak kVA (or kW) over the billing period, plus explicit power factor penalties when PF drops below a threshold like 0.9. The numbers make correction an easy business case. A factory drawing 500 kW at 0.75 PF presents 500 ÷ 0.75 = 666.7 kVA of demand; at $10 per kVA per month that is $6,667 in demand charges. Correct to 0.95 PF and demand falls to 500 ÷ 0.95 = 526.3 kVA — $5,263 per month, saving roughly $1,400 every month for a capacitor bank that typically pays for itself within a year.
Even without penalties, demand charges reward a high power factor: two factories consuming identical kWh pay different demand charges if one’s motors run corrected and the other’s do not. If you manage a facility, the first step is a power-quality analyzer on the main incomer for a week — it logs kW, kVA, kVAR, and PF around the clock, and the data sizes the correction exactly. The calculator above then converts any operating point between the three quantities in seconds.
You can verify all of this yourself with a plug-in power meter for single-phase loads or a clamp meter with power functions for three-phase. Measure kW, kVA, and PF on your largest motor loads and compare against the nameplate cos φ — a motor running at half load shows markedly worse power factor than at full load, which is itself an argument for right-sizing motors rather than oversizing “just in case.” Log the readings over a representative week, convert with the calculator above, and you will know exactly where a capacitor bank pays back and where it does not — no consultant required.
Common Mistakes
- Treating kVA as kW: the #1 generator-sizing error. A 45 kVA generator is not a 45 kW generator — at 0.8 PF it is a 36 kW generator.
- Adding kW and kVAR directly: 80 kW + 60 kVAR is not 140 kVA. Powers add as vectors: √(80² + 60²) = 100 kVA.
- Assuming PF = 1 for motors: real motors run 0.8–0.9. Using PF 1 understates kVA by 10–25% and undersizes the supply.
- Forgetting that kW can never exceed kVA: if your conversion gives kW > kVA, the power factor is wrong — PF is always ≤ 1.
- Sizing cables from kW: conductors carry total current, which follows kVA. Size from apparent power, via wire sizing.
Transformer Sizing Walkthrough
Putting it together, here is how a transformer gets specified. A small factory has 200 kW of real load — motors, lighting, HVAC — at an estimated 0.85 power factor. Apparent power is 200 ÷ 0.85 = 235.3 kVA. No manufacturer builds a 235 kVA transformer, and running any transformer at 100% continuously is poor practice, so add 25% growth margin: 235.3 × 1.25 = 294 kVA → the next standard size up, 300 kVA.
Now the secondary side: at 400 V three-phase, a 300 kVA transformer delivers 300000 ÷ (1.732 × 400) = 300000 ÷ 692.8 = 433 A per phase — that single number sizes the main breaker, the busbars, and the feeder cables leaving the transformer room. Notice the chain: kW and PF gave kVA, margin and standard sizes gave the transformer rating, and the kVA-to-amps conversion gave the current. Skip any link — size the transformer from kW alone, forget the margin, or cable from kW instead of kVA — and the installation fails somewhere expensive. The calculator above handles the first and last links in seconds; our kVA to amps calculator and wire size calculator cover the rest. Keep this chain in mind every time a nameplate shows kVA: convert to amps and kW first, then size everything downstream from those numbers.